Costco - Nexstyle Bermuda toilet - $88

[Slayguy]

Sorry guys for the lack of info but I should have taken a pic with more detail. Costco is selling a Nexstyle Bermuda Toilet for I believe $88 or $86. It's a dual flush and includes wax ring, toilet seat etc. I've never heard of Nexstyle toilets and can't find any info when googling it so therefore haven't purchased it yet but was hoping maybe someone can shed some light on this?

[xaveryptak]

Costco is selling a Nexstyle Bermuda Toilet for I believe $88 or $86. It's a dual flush and includes wax ring, toilet seat etc....maybe someone can shed some light on this?

anyone else have seen that toilet?
windsor has only regular WR

[shagnthings]

I'm looking at that same toilet. Costco told me they were made by "Quality Craft" http://www.qualitycraft.com
When I contacted the manufacturer they said the Bermuda HET Dual Flush Toilet is a special order by Costco. Their sales dept. emailed me a one page spec sheet. Not too much info on it .... probably the same amount of info listed on the box.
Trevor

[rks]

Has anyone had any reviews on this?

I bought a new house and the builder installed $30 toilets that take 2-3 times to flush correctly.

Thanks

rks

[97itr217]

Has anyone had any reviews on this?

I bought a new house and the builder installed $30 toilets that take 2-3 times to flush correctly.

Thanks

rks

I have installed 2 in my house, last 1 pending. First one went smoothly. Second one, not quite. Water leaked at where the tank-to-bowl bolt (RHS) is. Upon close inspection, I believe it is due to (1) holes (in the tank and bowl) not aligning properly and/or (2) the insulating foam got in the way of the rubber washer. Obviously better QC can probably rules that out. Fix was easy, but only after water dripping onto the floor.

My comments about it:
1. it works great (compare to the 13 LPF I replaced)
2. white is the only color
3. a bit higher than the one it replaces
4. super quiet when filling
5. everything included. Nothing more is required.
6. tank wobbles a bit when being pushed. May require something to fill the gap between tank and bowl.
7. very cost effective, consider I may be able to get $65 govt grant per unit. : )

[xaveryptak]

I'm looking at that same toilet. Costco
Have you seen it in the Windsor store?

[pipodayo]

I was in Costo - marche central - MTL yesterday and didn't seen one, but if someone know where to find it in Montreal area , please let me know !

[tanmanwayne]

If anyone gets the opportunity, could you take a picture and post? (I'll try to do the same if I get the chance as well!) :)

[markdweasel]

Saw them at Costco Woodbridge ( colossus) on Sunday. Lots there. I actually picked up the one piece Water Ridge model as I've installed 3 of them already without any issues. As other posters said, the two piece could pose some difficulty in respect to leaks. No such issues with the one piece. Yes, I paid over $50 more but I believe they're worth it.

York region gives back $75 per toilet. I am not 100% certain the Bermuda one is in the list although the WaterRidge is. I already got the rebates for the other 3 and just submitted the last one.

The water Ridge model has also the slow lid and seat, a must have if you have young children.

I love the waterRidge model and it is also extremely quiet on fillup.

Mark

[BinaryJay]

I'll be the first to say it.

Crappy deal.

[Miguel]

Saw them at Costco Woodbridge ( colossus) on Sunday. Lots there. I actually picked up the one piece Water Ridge model as I've installed 3 of them already without any issues. As other posters said, the two piece could pose some difficulty in respect to leaks. No such issues with the one piece. Yes, I paid over $50 more but I believe they're worth it.

York region gives back $75 per toilet. I am not 100% certain the Bermuda one is in the list although the WaterRidge is. I already got the rebates for the other 3 and just submitted the last one.

The water Ridge model has also the slow lid and seat, a must have if you have young children.

I love the waterRidge model and it is also extremely quiet on fillup.

Mark
I installed the waterridge one piece at my last house... I've been waiting for them to go on sale ever since I moved. I picked it up about 1.5 years ago for approx $115 and they haven't been back at that price since :cry:

[markdweasel]

I installed the waterridge one piece at my last house... I've been waiting for them to go on sale ever since I moved. I picked it up about 1.5 years ago for approx $115 and they haven't been back at that price since :cry:

I bought 3 last time they were on sale for 120. should have got one more. so stupid.

I also got tired of waiting as well so bought one. I had my final energy audit yesterday and I needed one last toilet. York region did extend the rebate but I am not sure for how long. It's nice to actually get paid to install a new toilet. with all the grants, I made ~$80 per toilet. Sweet!

Mark

[oldsnail]

from the COSTCO THREAD
http://forums.redflagdeals.com/costco-west-protein-stationery-brita-sofas-puffs-socks-laundry-rack-987727/

http://img508.imageshack.us/img508/1962/nexstyletwopiecetoiletd.jpg

[mangoman]

Love our 1-pc waterridge but haven't bought/had experience with this 2-pc.
Model is indeed on the latest (Dec. 15, 2010) MAP list under QualityCraft Bermuda EL ADA model 200119 and it's flush perfomance score is listed at 800 (the 1pc is listed at 500).

http://www.veritec.ca/uploads/latest%20MaP.xls

[Dave25]

Love our 1-pc waterridge but haven't bought/had experience with this 2-pc.
Model is indeed on the latest (Dec. 15, 2010) MAP list under QualityCraft Bermuda EL ADA model 200119 and it's flush perfomance score is listed at 800 (the 1pc is listed at 500).

http://www.veritec.ca/uploads/latest%20MaP.xls

MAP of 500 is low, even 800. I am looking to buy the American Standard Cadet 3 with a MAP of 1000.

[mangoman]

On paper 500 is low, but in practice, the 500 MaP rating on the 1-pc outperformed the toilet I bought with a rating of 1000, so MaP ratings are a crapshoot (pun intended)... go by actual user reviews if possible ( and the Cadet 3 should be sufficient however watch the trap opening if it's similar to the American Standard Mainstream - that thick toilet paper can clog it pretty easily).


MAP of 500 is low, even 800. I am looking to buy the American Standard Cadet 3 with a MAP of 1000.

[twtruck]

Had the Costco 2 pc unit installed since last summer. It has only once failed to get the job (pun intended) done!. No leaks, super quite comfortable and effective. Dual flush is great.

[mangoman]

Good to know, but I do believe this is a new model of the 2-pc (different manufacturer)?


Had the Costco 2 pc unit installed since last summer. It has only once failed to get the job (pun intended) done!. No leaks, super quite comfortable and effective. Dual flush is great.

[Matrixvibe]

Bermuda eh...sounds like a promising toilet, like the Bermuda Triangle...anything you put there will disappear. :lol:

[Mastermis]

we got 2 of the dual flush water ridge when they were 119$ 2 months ago or so. Very happy with them.

m.

[jhyang23]

I have 3 water ridge one piece toilets from costco.
They all have this intermittent problem where the water continues to run after large flush.
I had the flush valve replaced twice already and the problem keeps coming back.

[markdweasel]

I have 3 water ridge one piece toilets from costco.
They all have this intermittent problem where the water continues to run after large flush.
I had the flush valve replaced twice already and the problem keeps coming back.

Hmm, must be your batch. I got 3 of them and I don't have this issue.

Mark

[jhyang23]

Hmm, must be your batch. I got 3 of them and I don't have this issue.

Mark

Maybe but I see others with the same issue.

http://ths.gardenweb.com/forums/load/bath/msg0100450716571.html

[markdweasel]

Maybe but I see others with the same issue.

http://ths.gardenweb.com/forums/load/bath/msg0100450716571.html

Others? I see only two individual posts about your issue. So many more positive. I donno. I really love the toilets and, as I said in a prior post, bought another @ the regular price.

Mark

[mangoman]

The only times I've had the 1-pc run was due to operator error (my wife did not push the button completely down). At first I thought it was a bad valve tower, but after questioning her and having her not use that toilet for 2wks, it was definitely nailed down to operator error. :lol: To get it to stop, I turned off the water supply to the toilet for 30-45s. or so, then turned it back on and flushed it 'correctly'.


Others? I see only two individual posts about your issue. So many more positive. I donno. I really love the toilets and, as I said in a prior post, bought another @ the regular price.

Mark

[rks]

Bought a two piece berumuda to replace my 2 month old POS PRO Flo Toilet from my builder (they used WM Schmid). The pro flo would take 2-3 flushes for a number 2. This toilets number 1 button is better then that even!!!

The instructions and install was ok, except it seemed like they forgot to tell how to install the tank. After trial and error I figured it out. I am guessing they must sell this as a one piece somewhere else.

Overall for $88 this is awesome! Shame on you WM Schmidt for installing a toilet that can't do the job....


Edit: Apparently the water ridge (maybe even bermuda) toilet might be made by Danze! They make one of the better toilets on the market. Behold the power of an HET:

http://www.danze.com/flush_performance.asp

[Jamie_Canuck]

MAP of 500 is low, even 800. I am looking to buy the American Standard Cadet 3 with a MAP of 1000.

on sale this week at Lowes for $160 I do believe... round front, comfort height... $189 at Home Depot

[newfieinthefalls]

I have 3 water ridge one piece toilets from costco.
They all have this intermittent problem where the water continues to run after large flush.
I had the flush valve replaced twice already and the problem keeps coming back.

Yeah, ours just started having this problem two nights ago. Not happy.:(

[xaveryptak]

could somebody let me know what is the bowl height for both Bermuda and WaterRidge toilets?

[Keelie]

could somebody let me know what is the bowl height for both Bermuda and WaterRidge toilets?

Just installed the 2 piece Bermuda today. Rim height is 16 1/2".

I could not stand the horrible flush of our old toilet. So far this one is great, and refilling is super fast and quiet. I'm not thrilled about the seat, but that can be fixed easy enough.

[mangoman]

on another forum, it was mentioned that removing the flush mechanism, drying it out, spraying the internals/linkages in the mechanism with Jig-a-loo or a silicone or lithium based lubricant seems to help from the parts "sticking". Haven't needed to try this but a $5 solution seems worth a try.


Yeah, ours just started having this problem two nights ago. Not happy.:(

[mangoman]

Don't know who makes Danze's stuff, but the Wateridge 1-pc is made by a co. called Milim G&G Ceramics (in China of course) and the Bermuda 2-pc is made by a co. called Quality Craft (if you check their website it looks almost identical to the "Alexis").

http://www.qualitycraft.com/secondarynavigation/products/bathroom/toilets/alexishetdualflushtoiletbox


Bought a two piece berumuda to replace my 2 month old POS PRO Flo Toilet from my builder (they used WM Schmid). The pro flo would take 2-3 flushes for a number 2. This toilets number 1 button is better then that even!!!

The instructions and install was ok, except it seemed like they forgot to tell how to install the tank. After trial and error I figured it out. I am guessing they must sell this as a one piece somewhere else.

Overall for $88 this is awesome! Shame on you WM Schmidt for installing a toilet that can't do the job....


Edit: Apparently the water ridge (maybe even bermuda) toilet might be made by Danze! They make one of the better toilets on the market. Behold the power of an HET:

http://www.danze.com/flush_performance.asp

[Blitzo]

Is the Bermuda toilet bowl elongated (commercial sized) like the 1 pc. waterridge, or is it a standard size bowl? I want to buy one and install in the tenant's bathroom, but I don't have room for the commercial sized bowl.

[mangoman]

It's supposed to be an EL which means elongated but more importantly you should check the actual dimensions (the dimensions on the box in the costco thread pic was blurry but seemed to be close to the alexis on the quality craft site). I would either take a trip to Costco and check the dimensions or call up quality craft and ask them for the dimensions on the Bermuda model no. 016TQS060WHI


Is the Bermuda toilet bowl elongated (commercial sized) like the 1 pc. waterridge, or is it a standard size bowl? I want to buy one and install in the tenant's bathroom, but I don't have room for the commercial sized bowl.

[Keelie]

Is the Bermuda toilet bowl elongated (commercial sized) like the 1 pc. waterridge, or is it a standard size bowl? I want to buy one and install in the tenant's bathroom, but I don't have room for the commercial sized bowl.

It is elongated, but its also smaller than our standard sized one we replaced. A little higher, but that is it.

[xaveryptak]

Just installed the 2 piece Bermuda today. Rim height is 16 1/2".


thanks. went to the store today but couldn't find any measurments on the box.

[mangoman]

See where the picture of the button with the numbers "1" and "2" are in the lower left-hand corner in the turquoise square? Below that to the left of the Model no. 016TQS060WHI is where the dimensions are (from what I can read of the blurry text):

http://img508.imageshack.us/img508/1962/nexstyletwopiecetoiletd.jpg


thanks. went to the store today but couldn't find any measurments on the box.

[xaveryptak]

I read that in the store - but it looked like box dimensions for shipping. WaterRidge that was besides had rough in distance, height of the bowl and all the others listed in nice large print.

[Keelie]

I read that in the store - but it looked like box dimensions for shipping. WaterRidge that was besides had rough in distance, height of the bowl and all the others listed in nice large print.

I can look tomorrow and see if the measurements are on any of the instructions. Hubby put everything back into the box and its out in the garage, will check it out when I get home from work tomorrow.

[dosgringos]

Can anyone report back the installed height of the toilet from the floor up to the top of the tank? Thanks.

[97itr217]

Can anyone report back the installed height of the toilet from the floor up to the top of the tank? Thanks.

The answer is in #30 on page 2: (http://forums.redflagdeals.com/costco-nexstyle-bermuda-toilet-88-a-985584/2/#post12305068)

[dosgringos]

The answer is in #30 on page 2: (http://forums.redflagdeals.com/costco-nexstyle-bermuda-toilet-88-a-985584/2/#post12305068)

>:( No, it is not. Read the question.

[mangoman]

My guess from the Alexis model on the Quality Craft website would be close to:

Dimensions: H x W x L
Individual toilet
840mm x 455mm x 740mm
33.07" x 17.91" x 29.13"


No, it is not. Read the question.

[dosgringos]

My guess from the Alexis model on the Quality Craft website would be close to:

Dimensions: H x W x L
Individual toilet
840mm x 455mm x 740mm
33.07" x 17.91" x 29.13"

Yeah, I noticed that on their website, but that's not what I remember being on the box when I saw it at Costco...something like 30.5". I have an e-mail into their customer support, but I'd rather hear from someone who's actually installed it.

[dosgringos]

Thank you for your e-mail. Please see below for dimensions needed.

Dimensions: H x W x L
Individual toilet
770mm x 980mm x 730mm
30.31" x 38.58" x 28.74"

Regards,
Customer Service
Quality Craft

:confused: Width is certainly incorrect, I have asked for clarification by e-mail

[mangoman]

gotta be a mistake - that toilet is not 3ft+ wide!


Thank you for your e-mail. Please see below for dimensions needed.

Dimensions: H x W x L
Individual toilet
770mm x 980mm x 730mm
30.31" x 38.58" x 28.74"

Regards,
Customer Service

[Keelie]

:confused: Yeah, I noticed that on their website, but that's not what I remember being on the box when I saw it at Costco...something like 30.5". I have an e-mail into their customer support, but I'd rather hear from someone who's actually installed it.

From floor to top of tank is 29.75", but that is at the side, it slopes up in the center of the lid where you flush and that might be 1-1.5" higher if I had to guess?

Looks like box and instructions all went into the recycling so cant say for sure. If you need any more measurements I'm happy to help.

[dosgringos]

From floor to top of tank is 29.75", but that is at the side, it slopes up in the center of the lid where you flush and that might be 1-1.5" higher if I had to guess?

Looks like box and instructions all went into the recycling so cant say for sure. If you need any more measurements I'm happy to help.

:) Thank you that's great, now I'm sure it will fit.

[xaveryptak]

Hubby put everything back into the box and its out in the garage, will check it out when I get home from work tomorrow.
are you returning the toilet?

[retraite]

please delete

[retraite]

I was in Costo - marche central - MTL yesterday and didn't seen one, but if someone know where to find it in Montreal area , please let me know !

You can find it (and the monopiece as well) at the Costo, in Laval. My sister just bought one to-day !

[Keelie]

are you returning the toilet?

No instructions were put back into the box, thought it might have the measurements in there somewhere.

Toilet is great, cant beat it for the price... BTW, it's 84.99 here.

[dosgringos]

gotta be a mistake - that toilet is not 3ft+ wide!

Nope, here is the exact width :


14.96 '' should be the width of the toilet

Regards,
Customer Service
Quality Craft

[txenglan]

Anymore feedback on these? I was tempted to buy three at my local store today but held off due to mixed reviews herein.

[rks]

There are two toilets here:

Nexstyle Bermudea (85$) and the WAter Ridge Toilet. Some people had issues with the WR toilets. I installed three Bermuda Toilets and they are fantastic!!!

Sure beats the ProFlo builder grade toilets in my house!!! The glazing is high quality so stuff doesn't sink. The number 1 flush does the job for everyything most of the time!!!

rks

[txenglan]

There are two toilets here:

Nexstyle Bermudea (85$) and the WAter Ridge Toilet. Some people had issues with the WR toilets. I installed three Bermuda Toilets and they are fantastic!!!

Sure beats the ProFlo builder grade toilets in my house!!! The glazing is high quality so stuff doesn't sink. The number 1 flush does the job for everyything most of the time!!!

rks

Thanks. I found the comments a bit confusing and sometimes wasn't sure which toilet was being referenced. With the type of glowing review you've given, I might just take the "plunge(r)" ;)

[Slayguy]

Bought the Bermuda toilet last weekend and installed it and so far it's great. We didn't have a big space to put this toilet and as it says on the box it's a space saver which it definitely is. As someone mentioned before it's made by Quality Craft so be sure to look for that make when searching the approved toilets for a refund from the City.

[phht]

Does anyone know if the water ridge toilet is qualified for toronto rabte? someone said it was qualified for York rebate. Thanks

[Jamie_Canuck]

Was just at Castco in Kitchener, they only have the Water Ridge, one piece, dual flush... and it's $139... not a great deal, it would appear...

[dosgringos]

Anybody see more of these in store either in Ottawa-Gatineau or Laval? Thanks.

[mangoman]

Actually the one-piece wateridge is still a pretty great deal to me (but I agree at $88, the Nexstyle is cheaper and may even pay you with city rebates) - looks quite nice and is quicker to install if you have 2 ppl to position it. Good Luck finding something similar that actually works/flushes as well outside of Costco.


Was just at Castco in Kitchener, they only have the Water Ridge, one piece, dual flush... and it's $139... not a great deal, it would appear...

[txenglan]

I caved in and bought the Bermuda tonight. Before I did, I went to Rona since they have a sale on as per:

http://forums.redflagdeals.com/rona-1-piece-elongated-toilet-dual-flush-half-price-119-till-march-15-a-1010732/

....Which I believe is this one: http://www.rona.ca/shop/~toilet-elongated-1-piece-toilet-uberhaus-438900_toilets_bathroom_uberhaus_kitchen-bathroom_shop

Anyhow, when I got to Rona, I found that they had no stock left on that one so they were willing to sell the following in-house model for $119 (reg $249): http://www.rona.ca/shop/~toilet-dual-flush-toilet-rona-collection-178222_toilets_bathroom_rona-collection_kitchen-bathroom_shop

Anyone care to wade in on which, out of all three models is the best deal? Would much appreciate as I won't hesitate to take the Bermuda back if I haven't made the right decision.

[jackass_ca]

Sorry to drag this thread up again, I bought one in London, went back to get another, they are sold out, in both stores in London. Not sure about Windsor which is next closest for me, but in our guest bathroom, I can't use the elongated seat anyhow, the knees would be pretty close to the opposite wall... seat height is 16" and yes, the specs are on a tiny little label on the bottom of the box, full length, back to front is 28.75" I think the round bowl I have in there now is something like 26".
As far as mAp scores, I found the OPAL toilet at Rona locally here, going to pick it up tonight, for $79, no seat. However, it is the standard bowl, single 6l flush, and 1000 mAp score... the one that it is replacing is 13l... I used to think it was just slow to fill, but found out, it was just a water pig!
I think for the energy rebates, you need minimum 360 mAp score. Anyhow, I wish I could have fit 2 of these dual flush models in our house, but no dice...

[xaveryptak]

Not sure about Windsor which is next closest for me, ...

I haven't seen any in last few weeks.

[mangoman]

Saw the Nexstyle Bermuda back in stock in Kanata @ ~$86.


I haven't seen any in last few weeks.

[liviu23]

If anyone spots one in Montreal area, please let me know. Thanks!

[Error2]

Just bought one $84 at Costco, Marche Central. At least 10 on the shelf. Haven't installed it. it's possible the cheapest toilet with a slow-close toilet seat. A slow-close seat for my Duravit costs $150, seat alone.

[chaccaracca]

Pickes up three of these toilets tonight at Kanata.

$84.99 each

1 new one left on the shelf.

Going to replace our junkstore builder toilets and use the third one in our new basement bathroom.

Hope they are as good as everyone says they are!

[JohnyBGood]

Are any quality rebate-eligible toilets on sale right now for June 2011? I'm looking to buy two, so regular price isn't in the cards and 2X $75 York Region rebates will be greatly welcomed.

Based on written reviews, I had decided on the Cadet 3, but craftsmanship seems to be REALLY unpredictable according to YouTube reviews (where some don't want to flush, while others perform like champs). There seems to be a quality control issue at American Standard and since I'll be using a plumber, the labour costs of replacing a toilet that my not even be refundable isn't something I want to chance with Cadet 3. Thank you VERY much in advance for any advice/tips/suggestions.

[Error2]

Box says "may be eligibible for rebate". I bought another three last week at Boucheville, installed one yesterday. No problem what so ever. Everything is included - wax and screws. Nice looking toilets