[Merged] Windows/Doors

[renoboy]

Thanks for your responses. The transom is a half round, so it might be difficult to use capped wood, but the backer rod would probably work to add some stability. I will measure the width of the caulking again to see if it is worth taking off and redoing with the backer rod in behind it. It sounds like if it is closer to one inch max it might be better to leave well enough alone. If that is the case, do you think the caulk will form a proper bond with the spray foam that is there and not have a difficulty with expansion/shrinking over time?
I am just surprised that a custom ordered door can be so off. Is that common?
I really appreciate you sharing your expertise.

can you post some good pictures ?

[anotherwindowpro]

usual disclaimer: I'm Phil Lewin - VP Marketing of Vinyl Window Designs Ltd. and a member of a variety of govt and ngo tech committees.

If you leave it as is and keep an eye on it, you can always do something if the caulk starts to show signs of wear before any damage is done to the home. But, I would inform the installer in writing that you are taking a wait and watch approach so, if you need his assistance down the road, he knows that the issue goes back to the installation. FYI, there are flexible or bendable products that can properly fill the area. Cellular PVC jamb board, for one.

Thanks for your responses. The transom is a half round, so it might be difficult to use capped wood, but the backer rod would probably work to add some stability. I will measure the width of the caulking again to see if it is worth taking off and redoing with the backer rod in behind it. It sounds like if it is closer to one inch max it might be better to leave well enough alone. If that is the case, do you think the caulk will form a proper bond with the spray foam that is there and not have a difficulty with expansion/shrinking over time?
I am just surprised that a custom ordered door can be so off. Is that common?
I really appreciate you sharing your expertise.

[tosca1]

Good suggestion. I will follow up with the installer with a paper trail. Thanks for the info about the other materials as well. That might be an option if we go ahead with a re-do.
Thanks again for your help.

[Ticket]

Just thought I'd post a follow up to the window/draft/cold temperature problem my relative had after installing new windows.

An installer came back and inspected the windows and found that some of the windows had manufacturing defects. Some gaps which caused drafts. Someone came and did some repairs and the problem is somewhat resolved. There are other issues with the install but things are moving at least.

[merry53]

We have been looking at one brand of windows that has a mohair strip on the casement windows. Can anyone tell us if these a poorer choice than having rubber bulb type weatherstripping?

[anotherwindowpro]

usual disclaimer: I'm Phil Lewin - VP Marketing of Vinyl Window Designs Ltd. and a member of a variety of govt and ngo tech committees.

By "mohair strip" I'm assuming you are talking about a seal that is designed for sliding. because casements can close like a door, they can use compression seals, like your fridge and car door. Compression seals have the advantage of being tighter, but can't slide, which is why a company like ours uses them in casements and on the closing side of many vertical and horizontal windows.

That being said, in a casement, the design should have the strongest seal in, working toward the weakest seal out, so any air pressure that builds up is forced to the outside and not inside your home. usually, the outermost seal is more cosmetic than trying to create an air barrier and could be a flap or the type of seal I think you are talking about, however, I would not chose to use that seal throughout the window because, by not using compression seals, you miss the opportunity for a tighter window.

We have been looking at one brand of windows that has a mohair strip on the casement windows. Can anyone tell us if these a poorer choice than having rubber bulb type weatherstripping?

[Gecko169]

Hi.......I'm new here and appreciate the comment and info in this thread. I've been looking at windows for my new addtion and Pollard Windows seems to have a good overall pacakge. Any comments would be apprecaited.

[kayee]

Hi, I would like to install a security door. Where can I get affordable security door in GTA? Or, if someone please recommend me a good contractor in GTA, that would be really great. Thanks.

[psilos]

Were the last 10-15 pages on this thread repeated?

[smartcar8]

I have a large bedroom window that has 3 individual windows (2 that open and a centre one that does not). The middle one has a broken seal so there is a lot of moisture between the 2 panes of glass. The window with the broken seal is 18" X 42". The windows are a vinyl type but I am not sure of the manufacturer as they were installed before we bought the house.

I don't want to replace the entire window and would rather just get the middle window replaced. Is it possible to do this? Any suggestions on who to call for a quote?

Thanks!

[anotherwindowpro]

usual disclaimer: I'm Phil Lewin - VP Marketing of Vinyl Window Designs Ltd. and a member of a variety of govt and ngo tech committees.

No need for a whole window. Any glazier can measure and replace the sealed unit!

If you look between the two panes of glass, you may see a code or name. In an IGMA certified sealed unit, this can be traced back to the original manufacturer, but is not essential if all you want to do is buy a new sealed unit.

I have a large bedroom window that has 3 individual windows (2 that open and a centre one that does not). The middle one has a broken seal so there is a lot of moisture between the 2 panes of glass. The window with the broken seal is 18" X 42". The windows are a vinyl type but I am not sure of the manufacturer as they were installed before we bought the house.

I don't want to replace the entire window and would rather just get the middle window replaced. Is it possible to do this? Any suggestions on who to call for a quote?

Thanks!

[smartcar8]

Between the panes it says: Laserseal Insulating Glass Ltd

I live in Toronto - any suggestions for glaziers who do this sort of residential work? I looked on Google but didn't find any.

Thanks again for all the help.

[Bronson Charley]

Does anyone have Jeld wen windows and doors installed? How are they performing?

Thanks

[adanac7152]

Between the panes it says: Laserseal Insulating Glass Ltd

I live in Toronto - any suggestions for glaziers who do this sort of residential work? I looked on Google but didn't find any.

Thanks again for all the help.

Look under glass in your local yellow pages or you can try a local window and door company, either way it is easy to have replaced and takes about 30 minutes to do once they arrive with the glass.

[Gecko169]

Narrowing down my search for windows and found Ostaco, All Weather or Vinyl Built to be workable - any thoughts?