Home & Garden

DIY: Wainscotting [Post 689]

  • Last Updated:
  • Dec 2nd, 2020 10:39 am
Deal Fanatic
User avatar
Jan 6, 2002
5753 posts
5908 upvotes
Toronto
Red_Army wrote: I thought I read him say that he is an amateur. 🤷‍♂️
Perhaps a well-to-do amateur who spent his money on tools instead of beanie babies?
A glass of wine with you, sir, and the ladies I'll enjoy.
Revolutionary times must on occasion make do with considerable abridgements in order to accentuate the political line more strongly.
[OP]
Sr. Member
Sep 5, 2011
644 posts
833 upvotes
Toronto
hoob wrote: Perhaps a well-to-do amateur who spent his money on tools instead of beanie babies?
Red_Army wrote: I thought I read him say that he is an amateur. 🤷‍♂️

I like to collect things. Started with stamps, evolved into currency and now tools. Have been collecting tools since 2002 (noticed most of my tools are in brand new conditions? Some are still in their original retail boxes)
[OP]
Sr. Member
Sep 5, 2011
644 posts
833 upvotes
Toronto
Heavy Duty Bunk Bed Build

Before I can officially call the second floor renovation complete, I need to build all oversized furniture first to reduce the amount of damages caused by moving things around. This week, I tackled the bunk bed for my daughters. I personally hate bunk beds but when you have more kids than bedrooms, I have no choice.

Based on my calculation, this bunk bed weights about 400lbs. After some research, I saw a lot of people intentionally leave the plywood edges exposed. I thought it might be fun to do the same especially I will be using Baltic birch for this build.

I started by making the headboard & footboard. These are structural so went a little overboard with these panels. To cut down on the weight a little bit, the inner panel is not solid. I joint all of the pieces with floating tenons with no metal hardware in case I need to drill into it later.

Image

Glued the panels together to make the inner frame

Image

Laminating the Baltic birch plywood on both side of the inner frame making the boards about 2-1/4" thick that weights about 130lbs each.

Image

I thought it would be nice detail to add a few exotic wood strips in between to breakup what otherwise would be just the boring plywood sheets.

Image

This is what the exposed plywood edge look like

Image

I then moved onto the bed rails. Pretty simple really. It consists of one 5-1/2" rail, one 1-1/2" supporting rail and a bunch of spacers for the bed slats.

Image

Dry fit one of the rail into the bed frame

Image

The bed slats are simple enough, it is just 3/4"x2-1/2"x38.5". Roundover all of the edges to make it more kid friendly.

Image

Prefinished the slats

Image

Dry fit the rest of the rails and slats

Image

Next is the ladder for the bed. Started with the ladder rails. I doodled a design that I think looks good on the wood and started cutting it out with a jig saw and finesse it with a rasp until I have the shape that I like.

Image

Once, the first rail is done, I just traced it to another piece and do the mirror copy of it.

Image

Cutting the mortise for the ladder rungs and dry fit it.

Image

Once I am satisfied with the look, I roundover all of the edges and glue them together.

Image

Installed the ladder onto the bed

Image

Make the bed guard for the upper bed with frame and panel & acrylic sheets. Dry fit the whole bed to make sure everything still fits.

Image

Dismantle the bed stain the rails, ladder and bed guard.

Image

The bunk bed in its final location.

Image

Image
Sr. Member
Nov 9, 2011
951 posts
932 upvotes
Toronto
PCShutters wrote: Image
Love the minimalistic look, especially the headboard & footboard; I hate cleaning those bunk bed with built in shelves - I can't seem to keep the dust off it.
[OP]
Sr. Member
Sep 5, 2011
644 posts
833 upvotes
Toronto
tonershop wrote: Love the minimalistic look, especially the headboard & footboard; I hate cleaning those bunk bed with built in shelves - I can't seem to keep the dust off it.
Thanks. That is what I was going for but unfortunately I again have to do exactly just that because the ladder is not very functional.
[OP]
Sr. Member
Sep 5, 2011
644 posts
833 upvotes
Toronto
Due to space constraints, I have to go with a ladder design that take the least amount of footprint. Unfortunately, it doesn't work. Climbing up is not too bad but going down is difficult because it is too steep.

To address the issue, I have decided to build a real set of stairs to go up to the upper bunk. Started with making the ledges for the first step.

Image

Making a template for the first step

Image

Transfer it to the plywood and cut it out

Image

Rinse and repeat to make the other 2 steps and put a few coats of clear coat on it.

Image

Installed the first step

Image

Install the support for the second step

Image

Second step installed

Image

Installed the last step. This is the highest I can go because I don't want to block the window shutters from opening. I also have to cut the footboard shorter to make climbing onto the upper bunk easier.

Image

Checking to make sure the shutter still opens.

Image

Final pictures

Image

Image

Image
[OP]
Sr. Member
Sep 5, 2011
644 posts
833 upvotes
Toronto
Kitchen Renovation

I was going to wait until I finish the kitchen renovation before I post this topic but this project is so big that it would take forever to complete so I thought I might as well post my renovation in progress instead.

This is my old kitchen. Typical L shape builder grade 100 sqft kitchen.

Image
Image

Because my old kitchen cabinets were still in a decent shape. I posted it on Kijiji for free and it was gone within minutes. A very nice couple came and dismantle my entire kitchen and haul it away in a few hours time. I didn't have to do anything. While at it, I offered them my bathroom vanities, mirrors, doors, bath tubs, etc...they took it all! I didn't even have to get one of those dumpster for my entire house renovation.

Image

Removed the bulkhead, ran a few pot lights and relocate a few receptacles based on my new kitchen layout.

Image

Replaced the drywall and put on the first coat of mud

Image

Image

Rip out the old tiles and subfloor and replace it with plywood. To see my tile job, see post #177

Image

Image

Image

Enlarge the exhaust fan vent to 8"

Image



Finally, I get to the cabinets. I spent 2 days reading all of the appliance manuals and planned out my kitchen layout. I am getting rid of the breakfast area and make the entire room a kitchen so I have approximately 170sq to work with. I started the planning on a piece of paper and transferred it onto the wall to get a better visual on the actual sizes of the cabinets.

Image

Once I am happy with the layout, I prepared the cut list and cut out most of the parts I will need. There are so many pieces...

Image

Image

And more pieces...Did I mention how much wood is required for this build??

Image

After I have most of the pieces cut down to more manageable sizes, I pre-finish it with water-based poly.

Image

Once dried, I get to assemble the carcasses. If you have it well planned out, it doesn't take very long. My brother and I built & hung these upper cabinet carcasses in one Sunday.

Image
Deal Addict
Feb 22, 2007
1948 posts
217 upvotes
Mississauga
i love the taping idea on the wall to visualize
Deal Addict
Apr 26, 2003
1159 posts
416 upvotes
This thread is crazy!!! DIY build your own kitchen cabinets from scratch!?!?! Are you a contractor by trade or just a super DIY guy? Subscribed to this thread!
[OP]
Sr. Member
Sep 5, 2011
644 posts
833 upvotes
Toronto
exrcoupe wrote: This thread is crazy!!! DIY build your own kitchen cabinets from scratch!?!?! Are you a contractor by trade or just a super DIY guy? Subscribed to this thread!
Thanks but I am just your average joe DIYer with access to some better than average tools. Money-mouth Face
[OP]
Sr. Member
Sep 5, 2011
644 posts
833 upvotes
Toronto
pardnme wrote: i love the taping idea on the wall to visualize
Yes that is one of my better use of time and effort. It not only help me visualize my kitchen better but it also act as a “map” for my kitchen build because there are so many components. It is easy to forget or misplace a workpiece.
Deal Addict
Feb 24, 2008
2905 posts
1500 upvotes
Mississauga
PCShutters wrote: Thanks but I am just your average joe DIYer with access to some better than average tools. Money-mouth Face
What the hell is your day job? Lol

Amazing work
[OP]
Sr. Member
Sep 5, 2011
644 posts
833 upvotes
Toronto
mau_mau wrote: What the hell is your day job? Lol

Amazing work
Thanks. I build window shutters for a living.
Deal Addict
Apr 26, 2003
1159 posts
416 upvotes
PCShutters wrote: Thanks but I am just your average joe DIYer with access to some better than average tools. Money-mouth Face
You are NOT an average DIYer! Looking at some of the stuff you've done in this thread is scaring the crap out of me, especially the plumbing stuff. I DIY'ed my own basement and did everything EXCEPT plumbing because I had my own nightmare story that will have to wait for another day to tell.

Are you living in the house while you're doing all of this?
Deal Fanatic
User avatar
Oct 15, 2007
5115 posts
2531 upvotes
exrcoupe wrote: You are NOT an average DIYer! Looking at some of the stuff you've done in this thread is scaring the crap out of me, especially the plumbing stuff. I DIY'ed my own basement and did everything EXCEPT plumbing because I had my own nightmare story that will have to wait for another day to tell.

Are you living in the house while you're doing all of this?
TBH some of the plumbing isn’t done to code, what is shown least. Can’t speak for what isn’t shown, but based on descriptions, it may not be either
Everything has been said before, but since nobody listens we have to keep going back and beginning all over again. - Andre Gide

Top

Thread Information

There are currently 2 users viewing this thread. (0 members and 2 guests)